Type of Rig | It should be Reverse Rotary Hydraulic Rig. |
| There is no such such thing called a hydraulic Reverse rotary rig and the queries you need to be clarified need to be addressed at the primary stage. |
Chassis | Ashok Leyland NT with certified Overhauled Engine with new |
| Tires and 6?4 Drive. |
| STANDARD LEYLAND NT WITH CERTIFIED OVERHAULED ENGINE AND NEW TYRES WITH 6X4 DRIVE |
Scope o1 Supply | Supply of Truck Mounted Reverse Circulation Hydraulic Rotary Drilling Rig Ca rulile o1? drilling upto 457meter (1500?)ft from BGL with 24? diameter complete in all |
| respects with Threaded Drilling= Pipes of 6? dia.x 7mni thickness. |
Drill Bit | Give us picture with dimensions and specs. |
Auger Bit | Give us ricture with dimensions and specs. |
Drilling Formation | oft and Hard Soil (Sand, Clay, Sandy Clay and Rock Layers) YES FOR ALL TYPES |
Drilling Capacity | 1500 ft(457nietei) Depth YES CONFIRMED |
Drilling Diameter | 30?(750mni) upto say 150?ft depth and 24?(600 mm) up to 1500?ft de r th |
| YES CAN BE ACHIEVED WITH AIR INDUCTION SYSTEM |
Mast Height from Drilling | 6.5rn to 6.7rn (From the Ground it may be 7.5m to bm.) |
Table | YES CONFIRMED |
Mast Capacity | Weight Lil?tin Capacity: 25 ton |
| Built with 75mm dia steel tubes of suitable thickness capable to bear a load of 80 tons, total height from GL is approx. 27ft. |
| |
| |
Hciglit of the Drilling Tab1c morn Ground | About 1meter (1050 mm) |
Rig Width and Length | 8?ft x 22?ft (2.44m x 6.7m) |
| 7.5 to 8m (With Mast in Vertical condition) |
Drilling Table Size | OD 787.5mm, ID 686rnm and Height 200mna |
Center Hole Dia. of the Drilling Table | 686mm |
Description of the Drilling Table | The Table is to guide the Drilling Pipe cluring Drilling and |
| also guides the lowering of the Upper Well Casin=q and Lower Well Casings Pipes of 457mm dia. OD and 219.1mm OD respectively. The Table shall be in 2 It:iIves. One Half shall remain Fixed rind attached with tlic Rig Frame and the other |
| |
| Part shall be hiiiq?ed with the Fixed Part. This Part is taken aside to oren the Table when necessary. (To fill in the Gap, we shall put another Round Part with 585mm OD and 178rnn lD x |
| |
| 200nirn thickness. We shall make this item coursel) |
Size and Type of Drilling Pipe | 150 mm ND x 7.1mmWT in 3m or 10?ft lcngths Male-Female Standard Threaded Ends easy coupling. OR with 1S0m m ND x 23mm Thick concentric Flanges with 8 holes, 2 Dowel Pins, 8 Nos. Bolts and Nuts, Washers and Rubber G askets. |
| Box mounted type hydraulic levelling jacks |
| The above jacks are provided with ?reverse flow restricted valves? to ensure safe operation. |
Mast Rising Cylinder | |
Cylinder Bore | 125 mm |
Stroke | 800 mm |
| The Drill Rig is equipped with a hydraulic cylinder for Raising & Lowering of the Mast Structure. |
Breakout Wrench | |
Cylinder Bore | 80mm |
Stroke | 300mm |
| The drill rig is equipped with hydraulic break out wrench for making and breaking of drill rods. |
Water Injection | |
Maximum Flow | 50 LPM |
Pump | |
Maximum pressure | 40 kg/cm2 |
Airline lubricator | Suitable to 1075cfm @ 275psi compressor |
Paint | Epoxy & Polyurethane paint |
| Anti- Corrosion to any type of environment epoxy paints to maintain the more life time of the equipment. |